I did the Patch update today and I am working on a project which I cannot snap to certain things on the overlay. Like stairs for example. Is this just me or part of the patch. I thought that I could do it on 2016 before. I use overlay a lot.
Overlay Snaps
#2
Posted 02 April 2015 - 08:55 AM
Almost seems like your zoom level plays a part in snap grabbing with the overlay.
#4
Posted 02 April 2015 - 02:20 PM
Just to verify .... 2014 snaps to all 4 corners and the centres of top, bottom and each side of the stair overlay. Don't see any reason why 2016 doesn't do the same.
There are 10 types of people in this world ....... Those who understand binary, and those who don't.
Softplan user since version 5.5.2.5
www.homehardwarekingston.ca
#5
Posted 02 April 2015 - 06:52 PM
Align to edge isn't working properly with overlays either. I submitted a ticket for both items.
#7
Posted 06 April 2015 - 09:46 AM
This problem is driving me nuts. (the below is foundation overlay to site plan)
http://youtu.be/WWL4dMHB5C8
#8
Posted 09 April 2015 - 09:57 PM
Extremely frustrating. I sent a support a message on this and here is what I got back. I had another issue with walls automatically raking when I used edit repeat to change a height on walls. So they know about it and are working on it.
"Development is currently working on a solution. Meantime, an edit of the wall to the correct height will need to be done. Can also use the Edit > Set Wall Height command rather than an Edit and Repeat Edit to change wall heights. Development is also working on a solution to allow Snap on overlay lines."
Brian Ficek
215 Airport Road
Bismarck, ND 58501
701.595.1696
www.facebook.com/FineLineDrafting.Bismarck.nd
www.fineline-drafting.com
SoftPlan user since version 9 (2003)
Current SoftPlan - SoftPlan+ 2018
AutoCAD user since R12 (1992)
Current AutoCAD - AutoCAD 2019 LT
#9
Posted 10 April 2015 - 07:11 AM
Thanks for bringing up the auto rake that was happening, its been happening to me alot also. I'm starting to give up suggesting stuff...very frustrating.
#10
Posted 10 April 2015 - 02:10 PM
Sorry for being a bit late to the party - but your conversation caught my eye. It is reassuring to know that the overlay snap is a bit intermittent, as I too run into this issue.
What I'm curious about, though, is whether or not you folks are having any issues with the perpendicular snap? I've noticed that while adjusting a wall, for example, the cursor will snap to one corner of the wall's end. Then, if I line up for a perpendicular snap, that particular corner will snap directly to the center of the wall's perpendicular location... resulting in a skewed wall and a disturbing lack of 90 degree angles! Perhaps this is a settings issue?
#11
Posted 10 April 2015 - 03:06 PM
That was an issue in 2014 too. It's not new.
There are 10 types of people in this world ....... Those who understand binary, and those who don't.
Softplan user since version 5.5.2.5
www.homehardwarekingston.ca
#12
Posted 10 April 2015 - 08:24 PM
Soren - Agreed, it has always been an issue for me. I have suggested a couple of versions in the past that the issue be fixed. I suppose to some extent I have gotten used to it, but it really needs fixed. The only way around is to turn the wall joins to zero and then use the extend command to extend the wall together.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users